歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

多槽手動超聲波清洗機：工業精密清洗的效率革命者

作者：創始人來源：http://www.400qy.cn/時間：2025-06-07

　　在精密制造、電子元器件生產及醫療器械加工等領域，多槽手動超聲波清洗機正成為解決復雜工件清潔難題的核心設備。其通過分階段工藝設計與超聲波空化效應的協同作用，可高效去除微米級污染物，顯著提升產品良率與生產線效能。

　　In the fields of precision manufacturing, electronic component production, and medical device processing, multi slot manual ultrasonic cleaning machines are becoming the core equipment for solving the cleaning problems of complex workpieces. Through the synergistic effect of phased process design and ultrasonic cavitation, it can efficiently remove micron level pollutants, significantly improving product yield and production line efficiency.

　　一、多階段清洗工藝的效率突破

　　1、 Efficiency breakthrough of multi-stage cleaning process

　　傳統單槽清洗機存在交叉污染風險，而多槽設計通過物理隔離實現工藝分段：

　　Traditional single slot cleaning machines pose a risk of cross contamination, while multi slot designs achieve process segmentation through physical isolation

　　預洗槽：采用60℃堿性清洗劑，通過循環噴淋去除工件表面90%以上切削液、防銹油等大分子污染物。某軸承制造企業實踐表明，預洗后顆粒物殘留量降低，減少主洗槽負荷。

　　Pre washing tank: Using 60 ℃ alkaline cleaning agent, more than 90% of cutting fluid, rust proof oil and other macromolecular pollutants on the surface of the workpiece are removed through circulating spraying. The practice of a certain bearing manufacturing enterprise has shown that the residual amount of particulate matter decreases after pre washing, reducing the load on the main washing tank.

　　主洗槽：配置40kHz超聲波換能器，產生空化效應使清洗液形成微射流，深入0.1mm以下盲孔清除金屬碎屑。對直徑5mm的噴油嘴清洗測試顯示，超聲波清洗使孔內殘留物減少。

　　Main washing tank: Equipped with a 40kHz ultrasonic transducer, it generates cavitation effect to form micro jets of cleaning solution, which penetrate into blind holes below 0.1mm to remove metal debris. The cleaning test on a 5mm diameter fuel injector showed that ultrasonic cleaning reduced residue inside the hole.

　　漂洗槽：使用去離子水進行三級逆流漂洗，電導率控制在5μS/cm以下，避免水漬產生。某連接器生產企業應用后，產品鹽霧試驗達標率提升。

　　Rinse tank: Use deionized water for three-stage countercurrent rinsing, with conductivity controlled below 5 μ S/cm to avoid water stains. After being applied by a connector manufacturing enterprise, the compliance rate of salt spray test for the product has increased.

　　烘干槽：采用紅外輻射與熱風循環組合，使工件表面水分蒸發時間縮短，避免氧化生銹。

　　Drying tank: using a combination of infrared radiation and hot air circulation to shorten the evaporation time of moisture on the surface of the workpiece and avoid oxidation and rust.

　　二、復雜結構件的清潔難題攻克

　　2、 Overcoming the difficulty of cleaning complex structural components

　　微小孔隙清潔：對燃油噴射系統0.3mm噴孔，超聲波清洗使孔內積碳清除率達，而傳統毛刷清洗僅能實現。

　　Micro pore cleaning: For the 0.3mm nozzle of the fuel injection system, ultrasonic cleaning can achieve a high removal rate of carbon deposits inside the nozzle, while traditional brush cleaning can only achieve this.

　　異形表面處理：渦輪葉片曲面夾角處的碳化鎢涂層殘留，通過超聲波空化剝離技術可實現100%清除，避免流道堵塞風險。

　　Irregular surface treatment: The residual tungsten carbide coating at the angle of the turbine blade surface can be completely removed through ultrasonic cavitation stripping technology, avoiding the risk of channel blockage.

　　脆性材料保護：在石英晶振清洗中，通過調整超聲波功率密度至0.5W/cm2，使碎片率從3.2%降至，保障產品電性能穩定性。

　　Brittle material protection: In quartz crystal oscillator cleaning, by adjusting the ultrasonic power density to 0.5W/cm2 Reduce the fragmentation rate from 3.2% to ensure the stability of the product's electrical performance.

　　三、環保與成本控制的雙重優化

　　3、 Dual optimization of environmental protection and cost control

　　清洗劑循環利用：主洗槽配備油水分離器，通過聚結分離技術使清洗劑更換周期延長，廢液處理成本降低。某汽車齒輪廠實踐數據顯示，年清洗劑消耗量減少。

　　Recycling of cleaning agents: The main washing tank is equipped with an oil-water separator, which uses coalescence separation technology to extend the replacement cycle of cleaning agents and reduce the cost of waste liquid treatment. Practical data from a certain automobile gear factory shows that the annual consumption of cleaning agents has decreased.

　　能耗管理：多槽獨立溫控系統使預洗槽加熱功率僅需主洗槽的60%，整機能耗較單槽設備下降。

　　Energy management: The multi tank independent temperature control system reduces the heating power of the pre washing tank to only 60% of that of the main washing tank, resulting in a decrease in overall energy consumption compared to single tank equipment.

　　廢水減排：逆流漂洗工藝使廢水排放量減少，COD值控制在80mg/L以下，滿足三級排放標準。

　　Wastewater reduction: The countercurrent rinsing process reduces wastewater discharge and controls COD values below 80mg/L, meeting the third level discharge standards.

　　四、操作靈活性與質量追溯

　　4、 Operational flexibility and quality traceability

　　工藝參數可視化：人機界面實時顯示超聲頻率、溫度、時間等參數，某液壓件廠通過記錄清洗數據，實現工藝參數與產品清潔度的關聯分析。

　　Visualization of process parameters: The human-machine interface displays real-time parameters such as ultrasonic frequency, temperature, and time. A hydraulic component factory records cleaning data to achieve correlation analysis between process parameters and product cleanliness.

　　批次管理：支持200組工藝配方存儲，不同產品切換時間縮短，適應多品種小批量生產模式。

　　Batch management: Supports the storage of 200 sets of process formulas, shortens the switching time between different products, and adapts to the production mode of multiple varieties and small batches.

　　異常預警：當清洗液電導率超標或超聲發生器溫度異常時，設備自動停機并推送故障代碼，減少不良品流出風險。

　　Abnormal warning: When the conductivity of the cleaning solution exceeds the standard or the temperature of the ultrasonic generator is abnormal, the equipment will automatically shut down and push a fault code to reduce the risk of defective products flowing out.

　　本文由多槽手動超聲波清洗機友情奉獻.更多有關的知識請點擊:http://www.400qy.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.400qy.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

上一篇：低溫廢水回收設備適配條件是什么？
下一篇：低溫廢水回收設備：低溫礦井水處理設備熱能梯級利用技術介紹