在精密加工領域，鈦合金零件以其高強度、輕量化的特性備受青睞，但也因其表面敏感、易受損傷的特點，對清洗過程提出了近乎苛刻的要求。CNC 鈦合金專用清洗機的無損傷去污方案，就像為鈦合金零件定制的 “溫柔浴”，在徹底清除油污、碎屑的同時，小心翼翼地呵護著零件的精度與表面完整性，其中藏著一套精妙的技術邏輯。

　　In the field of precision machining, titanium alloy parts are highly favored for their high strength and lightweight characteristics. However, due to their surface sensitivity and susceptibility to damage, they also impose almost stringent requirements on the cleaning process. The non-destructive cleaning solution of CNC titanium alloy specialized cleaning machine is like a "gentle bath" customized for titanium alloy parts. While thoroughly removing oil stains and debris, it carefully cares for the accuracy and surface integrity of the parts, hiding a sophisticated technical logic.

　　清洗介質的選擇是無損傷去污的第一道防線。傳統清洗常用的強堿、強酸類清洗劑，雖然去污力強，卻可能對鈦合金表面造成腐蝕，形成肉眼難見的麻點或氧化層。因此，專用清洗機多采用中性或弱堿性的環保清洗劑，這類清洗劑的 pH 值通常控制在 6-8 之間，既能通過表面活性成分分解油污，又不會與鈦合金發生化學反應。部分清洗劑還會添加緩蝕劑，就像給鈦合金零件穿上一層 “隱形防護衣”，在清洗過程中主動吸附在零件表面，隔絕清洗劑與金屬的直接接觸，進一步降低腐蝕風險。對于 CNC 加工后殘留的極細切削液、乳化液，清洗劑中還會加入特定的乳化劑，將油脂類污漬乳化成微小顆粒，使其更容易被水帶走，實現高效去污與無損傷的平衡。

　　The selection of cleaning media is the first line of defense for non-destructive decontamination. The strong alkali and acid cleaning agents commonly used in traditional cleaning, although having strong cleaning power, may cause corrosion to the surface of titanium alloys, forming hard to see spots or oxide layers. Therefore, specialized cleaning machines often use neutral or weakly alkaline environmentally friendly cleaning agents, whose pH value is usually controlled between 6-8. These cleaning agents can decompose oil stains through surface active ingredients without undergoing chemical reactions with titanium alloys. Some cleaning agents also add corrosion inhibitors, just like putting a layer of "invisible protective clothing" on titanium alloy parts, which actively adsorbs on the surface of the parts during the cleaning process, isolating the cleaning agent from direct contact with the metal and further reducing the risk of corrosion. For the residual ultra-fine cutting fluid and emulsion after CNC machining, specific emulsifiers are also added to the cleaning agent to emulsify grease stains into small particles, making them easier to be carried away by water, achieving a balance between efficient cleaning and no damage.

　　清洗工藝的參數控制是方案的核心智慧。CNC 鈦合金專用清洗機的清洗壓力需要精準調控，過高的壓力可能沖擊零件表面，導致棱角磨損或表面粗糙度增加；過低則難以清除深孔、盲孔內的頑固污漬。通常會根據零件的結構復雜度和表面精度要求，將壓力設定在 0.3-1.5MPa 之間，對于帶有精密紋路或薄壁的零件，甚至?xí)捎酶偷膲毫ε浜隙啻吻逑础Ｇ逑礈囟鹊目刂仆瑯雨P(guān)鍵，溫度過高可能導致鈦合金表面氧化變色，過低則會降低清洗劑的活性。一般將溫度控制在 40-60℃，這個區間既能保證清洗劑的去污效率，又能避免對鈦合金的熱損傷。此外，清洗時間也需嚴格把控，通過預設程序確保零件在清洗劑中浸泡和沖洗的時間恰到好處，既不會因時間過短導致去污不徹底，也不會因時間過長增加損傷風險。

　　The parameter control of the cleaning process is the core wisdom of the solution. The cleaning pressure of the CNC titanium alloy specialized cleaning machine needs to be precisely regulated. Excessive pressure may impact the surface of the parts, resulting in angular wear or increased surface roughness; If it is too low, it is difficult to remove stubborn stains in deep holes and blind holes. Usually, the pressure is set between 0.3-1.5MPa based on the structural complexity and surface accuracy requirements of the parts. For parts with precision patterns or thin walls, even lower pressure is used for multiple cleaning cycles. The control of cleaning temperature is also crucial. If the temperature is too high, it may cause oxidation and discoloration of the titanium alloy surface, while if it is too low, it will reduce the activity of the cleaning agent. Generally, the temperature is controlled between 40-60 ℃, which can ensure the cleaning efficiency of the cleaning agent and avoid thermal damage to the titanium alloy. In addition, the cleaning time also needs to be strictly controlled, ensuring that the parts are soaked and rinsed in the cleaning agent for the right amount of time through pre-set procedures. This will not result in incomplete cleaning due to too short a time, nor will it increase the risk of damage due to too long a time.

　　多階段清洗流程的設計為無損傷去污再加一層保障。整個清洗過程通常分為預清洗、主清洗、漂洗和干燥四個階段。預清洗階段采用高壓噴淋的方式，先去除零件表面附著的大塊碎屑和浮油，減少主清洗階段的污漬負荷；主清洗階段則結合浸泡、噴淋和超聲波清洗，超聲波的高頻振動能深入零件的微小縫隙和復雜型腔，將藏匿其中的油污和細小組屑震落，而超聲波的功率會根據零件材質和結構進行調整，避免因功率過大產生空化效應損傷表面；漂洗階段使用經過凈化的純水，徹底沖凈零件表面殘留的清洗劑，防止清洗劑殘留形成新的污漬；最后進入干燥階段，采用低溫?zé)犸L(fēng)循環或真空干燥技術，在不損傷零件的前提下快速去除水分，避免水漬殘留影響表面精度。

　　The design of multi-stage cleaning process is to achieve non-destructive cleaning with an additional layer of assurance. The entire cleaning process is usually divided into four stages: pre cleaning, main cleaning, rinsing, and drying. During the pre cleaning stage, high-pressure spraying is used to remove large debris and floating oil adhering to the surface of the parts, reducing the stain load during the main cleaning stage; The main cleaning stage combines soaking, spraying, and ultrasonic cleaning. The high-frequency vibration of ultrasonic waves can penetrate into the small gaps and complex cavities of parts, shaking off hidden oil stains and small debris. The power of ultrasonic waves will be adjusted according to the material and structure of the parts to avoid surface damage caused by cavitation effects due to excessive power; During the rinsing stage, purified pure water is used to thoroughly rinse off any residual cleaning agents on the surface of the parts, preventing the formation of new stains due to residual cleaning agents; Finally entering the drying stage, low-temperature hot air circulation or vacuum drying technology is used to quickly remove moisture without damaging the parts, avoiding residual water stains that affect surface accuracy.

　　設備的特殊結構設計也為無損傷去污提供支持。清洗槽內壁通常采用惰性材料制成，如聚四氟乙烯或 316 不銹鋼，這些材料化學穩定性強，不會與清洗劑或鈦合金發生反應，避免對零件造成二次污染。清洗機的噴淋臂和噴嘴經過特殊設計，噴出的水流呈扇形或錐形，均勻覆蓋零件表面，避免局部壓力過大。對于易變形的薄壁鈦合金零件，還會配備專用的工裝夾具，將零件固定在合適的位置，防止清洗過程中因水流沖擊導致零件變形。

　　The special structural design of the equipment also provides support for non-destructive cleaning. The inner wall of the cleaning tank is usually made of inert materials, such as polytetrafluoroethylene or 316 stainless steel, which have strong chemical stability and will not react with cleaning agents or titanium alloys, avoiding secondary pollution to the parts. The spray arm and nozzle of the cleaning machine are specially designed to spray water in a fan-shaped or conical shape, evenly covering the surface of the parts to avoid excessive local pressure. For thin-walled titanium alloy parts that are prone to deformation, specialized fixtures will be equipped to fix the parts in the appropriate position and prevent deformation caused by water flow impact during the cleaning process.

　　本文由CNC高壓清洗機友情奉獻.更多有關的知識請點擊:http://www.400qy.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.400qy.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message