歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

CNC高壓清洗機多見的問題以及解決方法

作者：admin來源：http://www.400qy.cn/時間：2022-09-27

CNC高壓清洗機長時間運作時，設備也會出現一些小毛病，當故障出現時，操作員只需根據不一樣故障現象，細心查找原因，及時解決疑問即可。下面咱們首要介紹一些CNC高壓清洗機多見的問題以及解決方法。

When the CNC high-pressure washer operates for a long time, the equipment will also have some small problems. When the fault occurs, the operator only needs to carefully find the cause and solve the problem in time according to different fault phenomena. Here we mainly introduce some common problems and solutions of CNC high-pressure washer.

1、CNC高壓清洗機在作業的進程中假如呈現反常的尖叫聲，多見原因是因為電機軸承缺油致使的。只要在電機的注油孔寫入普通黃油就可以解決，這種狀況出現的不多。咱們在CNC高壓清洗機定時修理保護時給予彌補就可以了。

1. If the CNC high-pressure washer shows abnormal squeal during operation, the common reason is that the motor bearing is lack of oil. It can be solved by writing ordinary butter into the oil filling hole of the motor, which rarely occurs. We can make up for it when the CNC high-pressure washer is regularly repaired and protected.

2、CNC高壓清洗機在發動后，呈現壓力不穩定或時有時無，這里大都原因是高壓水泵或進水管路內吸入了空氣所致使的，這時需求查看水源的壓力是不是滿足，進水過濾器是不是阻塞，假如發現濾網阻塞,將濾網取下用水清洗就可以了。

2. After the CNC high-pressure washer is started, the pressure is unstable or sometimes absent. Most of the reasons are caused by the intake of air in the high-pressure water pump or water inlet pipe. At this time, it is necessary to check whether the pressure of the water source is met and whether the water inlet filter is blocked. If the filter screen is found to be blocked, remove the filter screen and clean it with water.

3、CNC高壓清洗機在作業的進程中有必定的作業壓力可是調不到設備的額外壓力或者說壓力只停留在必定范圍內而不能上升，在這種狀況下，要判別高壓噴嘴的孔徑是不是匹配。

3. The CNC high-pressure washer has a certain operating pressure in the process of operation, but the additional pressure of the equipment cannot be adjusted, or the pressure only stays within a certain range and cannot rise. In this case, it is necessary to judge whether the aperture of the high-pressure nozzle is matched.

如替換高壓噴嘴后壓力依然上不去，這時需求查看調壓閥是不是調到位了，假如在掃除這兩種狀況下故障照舊，這闡明泵內密封組件損壞或者是活塞損壞，這種狀況需求聯絡廠商幫忙修理。

If the pressure still cannot rise after replacing the high-pressure nozzle, check whether the pressure regulating valve is adjusted to its position. If the fault is still the same under these two conditions, it indicates that the sealing component in the pump is damaged or the piston is damaged. In this case, contact the manufacturer for repair.
CNC高壓清洗機

4、CNC高壓清洗機在正常作業必定時刻后壓力下降，這種狀況首要要查看高壓噴嘴是不是嚴峻磨損。其次需求分別查看調壓閥和水泵內部的密封組件。

4. The pressure of the CNC high-pressure washer drops after a certain time of normal operation. In this case, first check whether the high-pressure nozzle is severely worn. Secondly, check the pressure regulating valve and the sealing components inside the water pump.

5、啟動設備后，高壓水泵沒有水射出，這種疑問需求修理人員查看。大多數原因是進水流量閥不能打開造成的，假如掃除這種狀況下疑問照舊，那即是高低壓水路串聯了。

5. After the equipment is started, no water is ejected from the high-pressure water pump, which needs professional repair personnel to check. Most of the reasons are that the inlet flow valve cannot be opened. If the problem remains the same under this condition, it is that the high and low pressure waterways are connected in series.

此外操作者在使用過程中務必遵循相關的正確的原則，才能使高壓清洗機發揮出更好的作用。詳情內容了解就來我們網站www.400qy.cn咨詢吧！

In addition, the operator must follow the relevant correct principles in the use process to make the high-pressure cleaner play a better role. For more information, please visit our website www.400qy.cn!

上一篇：噴淋清洗機有哪些常規檢查事項呢？
下一篇：高壓去毛刺清洗機的正確操作方法